Beiträge von Lucano99

Zitat von Lucano99

Ahoj všichni.

Zkoušel jsem upgradovat kotel na dřevo a pelety s malým displejem na verzi: AWP 200303HC a po upgradu mám stále modrou obrazovku.

Původní SD kartu jsem již dříve zálohoval, ale z nějakého důvodu se SD karta nepřipojí.

Nemá tu někdo prosím jinou verzi firmwaru, kterou bych mohl zkusit? Napsal jsem na podporu výrobce, jestli by mi to nemohli poslat taky...

[Moderation] Hier die Übersetzung (Google Übersetzer):

Hallo zusammen.

Ich habe versucht, den Holz- und Pelletskessel mit dem kleinen Display auf Version: AWP 200303HC zu aktualisieren und nach dem Upgrade habe ich immer noch einen blauen Bildschirm.

Ich habe die ursprüngliche SD-Karte zuvor gesichert, aber aus irgendeinem Grund lässt sich die SD-Karte nicht verbinden.

Hat jemand eine andere Firmware-Version, die ich bitte ausprobieren kann? Ich habe den Support des Herstellers angeschrieben, ob sie mir das auch zusenden könnten...

Hi, it is attack Wood and Pellet,..

The fan is fine, as far as I know. Everything is clean.
Does anybody has experience with cleaning the combustion chamber? Must it be clean always, when you want to try to use pellets?

The temperature is usually about 160-180°C (I will try to raise it to the 200°C), but We were burning many briquettes, that might be the issue with the soots in the chimney. This year I want to burn only dry wood and pellets, so lets see.
Also, I will have a serviceman check, after 1 year, but everybody knows how they work.. - if you want to install new boiler, they are wery happy, if you want to service something, they dont have time.

Also, what is bothering me

• if you are running on pellets and the temperature of water reachs 85°C, which is the maximum, it stops with pellets, but it did not start again, instead of that it is showing some error message and playing annoying sound (anybody experienced?)

And one more thing

• if it is a time to add wood (temperature of exhausts is going down - like 120°C - and I open the main door, the boiler shuts off, I have to start it manually. (It probably has a flame sensor and if there is only glowing charcoal inside, it thinks it is time to shut it down). So I have to start it again.

I have ordered the ADDITIONAL FLUE GAS DRAUGHT FAN PV150 and we will see, how it will be working with that...

Hi,

yep, I saw some of these also, but, this require to have electricity on the roof and mounting to the chimney, but.. the attack part looks better. Can be powered by the same relay as the default fan is, so... very easy to connect. I just want to know, if this can be helpful with the smoke inside the room

Hello everybody,

Sorry, I am not good in German language, so I will write my issue in english, if you dont mind.

I have attack wood and pellet + 2000l tank. Problem what I have is that the exhaust from the boiler is a bit longer. About 150cm to the chimney and it goes very slightly up.
This spring, I cleaned the chimney and saw that the exhaust pipe is almost full of soots. So I vacuumed everything.

I have 7,5m high chimney, 200mm diameter, when I am going to add wood, smoke often goes out. I cleaned also the fan in the back of the boiler. DO you think that this http://www.attack.sk/en/pridavny-odtah-spalin/ will be helpful? Temperature of smoke is about 170-190°C . I was thinking to raise it up to the 200°C.

I have the newest software installed.

What also happened about 3-4 times is that, when I am going to start with pellets, it ends up after few minutes with a lot of smoke in the room.

Is anybody here using wooden chips?

Thank you!!